Encouraging Petrographic Results from the Mayview Prospect
Released
Released
Announcement PDF
ASX Announcement
12 February 2025
Encouraging Petrographic Results from the Mayview
Prospect, NSW
Highlights
•
Widespread Veining & Brecciation: Samples show significant hydrothermal quartz
veining, with textures characteristic of shallow mesothermal to epithermal
environments, indicating a structurally controlled mineralising system.
•
Comparison to Hillgrove Deposit: The textural and mineralogical characteristics of the
quartz infill in veins is similar to observed stibnite-bearing hydrothermal infill Sb-Au
quartz at the Hillgrove mineralised system, reinforcing Mayview's potential for further
exploration and development.
•
Antimony Mineralisation: Multiple samples contain remnant stibnite, which has been
extensively replaced by supergene antimony oxides, probably cervantite and
senarmontite, a process consistent with surface exposures of Hillgrove-type Sb-Au
systems.
•
Potential for Primary Antimony Sulphide (Stibnite) below oxidised zone: Although
supergene oxidation has replaced most primary sulphides, traces of stibnite were
preserved in many samples, (MVP14) retained substantial stibnite in vein infill.
Critical minerals exploration and project development company Critical Resources Limited
ASX:CRR (“Critical Resources”, “CRR” or “the Company”) is pleased to announce the results of
petrographic analysis conducted on eight rock samples from the Mayview Prospect, located
southeast of Hillgrove, NSW 1. The study, performed by Paul Ashley Petrographic and Geological
Services, confirms the presence of extensive quartz-sulphide veining, hydrothermal brecciation,
and significant supergene antimony mineralisation within low-grade metamorphosed sedimentary
host rocks of the late Palaeozoic Sandon Beds.
Recent Assay Results
These petrographic findings build on the exceptional assay results announced on 16 December
2024, which confirmed high-grade antimony (Sb) and gold (Au) mineralisation at the Mayview
Homestead Prospect, part of the Halls Peak Project.
Key Assay Highlights include:
•
52.3% Sb – Sample MVS17
•
38.3% Sb – Sample MVS8
•
31.8% Sb – Sample MVS14
•
29.7% Sb – Sample MVS6
•
15.35% Sb & 2.71 g/t Au – Sample MVS11
•
12.45% Sb & 2.18 g/t Au – Sample MVS18
1
Refer ASX announcement 16 December 2024.
Critical Resources Limited
ABN 12 145 184 667
ASX:CRR
Level 45, 108 St Georges Terrace, Perth WA 6000
P. +61 (8) 9465 1024 W. criticalresources.com.au E. info@criticalresources.com.au
These results confirmed the presence of high-grade antimony mineralisation, with some samples
exceeding 50% Sb, along with notable gold grades. The assays, combined with recent
petrographic work, reinforce Mayview’s potential as a significant Hillgrove-style orogenic Sb-Au
system.
Supporting Thin Section Data
1. Widespread Veining & Brecciation: Evidence of a Structurally-Controlled Hydrothermal System
Thin section analysis confirms that quartz veining and hydrothermal brecciation are extensive
across the sampled areas. These quartz veins display inequigranular to prismatic textures, comb
textures, and crystal-lined voids, which are characteristic of mineral deposition at shallow
mesothermal to epithermal depths.
•
MVP3 & MVP4: These samples display multiple intersecting quartz veins within fine-grained,
low-grade metamorphosed mudstone-siltstone host rocks. Veins are locally associated
with hydrothermal breccia zones, as seen in MVP4, where quartz-rich infill merges into
brecciated zones, confirming significant fluid movement and mineralisation potential.
•
MVP18 & MVP19: Both samples exhibit strong vein networks with cross-cutting quartz-rich
veins and hydrothermal breccia textures, indicative of repeated fluid influx. Quartz
textures further reinforce the shallow mesothermal to epithermal nature of the system.
2. Strong Antimony (Sb) Mineralisation with Widespread Supergene Alteration
Several samples contain relic stibnite, a primary Sb-bearing sulphide, but most of it has been
overprinted by supergene alteration, resulting in the formation of Sb oxide minerals, including
cervantite and senarmontite. These oxides are typical of weathered antimony deposits and
demonstrate significant potential for primary sulphide mineralisation at depth.
•
MVP5 & MVP11: Initially contained interstitial stibnite, which has now been almost entirely
replaced by supergene Sb oxides (cervantite and senarmontite). The oxidation is
particularly well-developed in MVP11, where central vein infill of former stibnite is now
replaced by Sb oxides with only rare relict grains of sulphides remaining.
•
MVP14 & MVP16: These samples represent the best-preserved examples of original stibnite,
with MVP14 retaining a large mass of coarse-grained stibnite, albeit showing deformation
and early stages of supergene oxidation. MVP16 contains a former stibnite-quartz vein,
where all stibnite has been converted to supergene Sb oxides, yet tiny relict grains remain
encapsulated in quartz.
3. Presence of Primary Sulphides (Arsenopyrite, Pyrite, and Stibnite) Suggests Potential for
Deeper, Untested Sulphide Zones
Although supergene oxidation has destroyed most primary sulphides, traces of arsenopyrite,
pyrite, and stibnite are still preserved in some samples, encapsulated within vein quartz.
These findings suggest potential that deeper, unweathered portions of a system could
contain preserved sulphide mineralisation.
•
MVP11 & MVP19: These samples contained a major compound vein with arsenopyrite and
pyrite at the margins. While most of the sulphides were replaced by goethite and Sb
oxides, rare tiny grains of arsenopyrite (~30µm) were retained in quartz veins, indicating
the original presence of sulphide mineralisation.
Page 2 of 23
•
MVP18: Retained minuscule encapsulated grains of stibnite, arsenopyrite, and pyrite,
demonstrating that some sulphides remain intact despite the widespread supergene
overprint.
4. Comparison to the Hillgrove Sb-Au System Strengthens Mayview’s Exploration Potential
The mineralogical and textural characteristics of the Mayview samples closely resemble the
Hillgrove Sb-Au deposit, a historically significant antimony-gold mining operation in New South
Wales. The presence of stibnite-rich veins with arsenopyrite and quartz textures typical of
mesothermal to epithermal systems aligns well with known mineralisation styles at the Hillgrove
site, located just some 2.7 km southeast of the Mayview prospect.
•
MVP14 & MVP16: These samples contain massive stibnite vein infill, similar to what is
observed at Hillgrove, where primary Sb-Au mineralisation is hosted in quartz-stibnite veins.
•
MVP5 & MVP19: Show significant hydrothermal brecciation, a feature commonly
associated with structurally controlled mineralisation in Hillgrove-type Sb-Au systems.
Figure 1: Halls Peak Project Area including the Mayview Homestead showing located proximal to Hillgrove
Mine
Page 3 of 23
Figure 2: Sample locations at Mayview Homestead Prospect. Located proximal to Larvotto Resources’
Hillgrove Mine Property and ~2.7km from the mine site.
Strategic Location
The Mayview Homestead Antimony Prospect is strategically located within the Company’s
extensive Halls Peak Project, in the highly prospective New England Fold Belt of New South Wales.
This region is notable for hosting Larvotto Resources Ltd’s Hillgrove Antimony-Gold Project, reported
as Australia’s largest antimony-gold system. Situated approximately 2.7 km east of Hillgrove,
Mayview presents an exciting exploration opportunity, with early indications suggesting it could
represent a continuation of the Hillgrove-style orogenic antimony-gold system.
Next Steps:
The Company plans to undertake further exploration activities at the Halls Peak project, including
geochemical sampling to identify and define mineralised zones more clearly; structural mapping
and potential trenching to understand vein orientation and distribution together with engaging a
specialist consultant geophysicist to carry out reinterpretation of closed-spaced heliborne VTEM
and magnetic survey to locate and map the Antimony-Gold structures, with the aim of testing
potential predicted extensions of the structural controls of the large scale of system and
define areas of potential new mineralisation at the Amoco target. Once all data is
compiled and reviewed the Company will design a detailed and thorough maiden drilling
campaign.
Critical Resources Director, Nigel Broomham, stated: “These results make Mayview an
exciting exploration prospect, showcasing the potential for significant antimony and gold
mineralisation. We look forward to advancing exploration to uncover its full potential.”
This announcement has been approved for release by the Board of Directors.
-ends-
Page 4 of 23
For further information please contact;
E: info@criticalresources.com.au
P: +61 (8) 9465 1024
ABOUT CRITICAL RESOURCES LIMITED Critical Resources is focused on the exploration, development and delivery of the
critical metals required for a decarbonized future. The Company’s Mavis Lake Lithium Project in Ontario, Canada,
where it has completed over 45,000m of drilling and defined a maiden Inferred Mineral Resource of 8Mt grading 1.07%
Li2O. Recent exploration success has demonstrated substantial potential to expand this resource and make new
discoveries in the surrounding area. Critical is progressing a dual-track strategy at Mavis Lake of targeting resource
growth in parallel with multiple permitting and project development workstreams.
The Company’s Hall Peak Base Metals Project is located 87km south-east of Armidale New South Wales, Australia, a
reginal hub in New South Wales. The Company has defined a maiden Inferred Mineral Resource of 884,000t grading
3.7% zinc, 1.5% lead, 0.4% Copper, 30ppm Silver and 0.1ppm Gold has been estimated following numerous drilling
campaigns. Modelling has shown that mineralisation is still open along strike to the east/north-east and west/southwest, providing immediate potential to increase the MRE with follow-up drilling.
COMPETENT PERSON, COMPLIANCE STATEMENT The information in this ASX Announcement that relates to Exploration
Results is based on information compiled by Mr Michael Leu, a Competent Person who is a member of Australian
Institute of Geoscientist (AIG) and the Australian Institute of Mining and Metallurgy (AusIMM) and a consultant of Critical
Resources. Mr Leu has sufficient experience that is relevant to the style of mineralisation and type of deposit under
consideration and to the activity being undertaken to qualify as a Competent Person as defined in the 2012 Edition of
the “Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves”. Mr Leu consents to
the inclusion in this Announcement of the matters based on his information in the form and context in which it appears.
This announcement contains information on the Halls Peak Project extracted from ASX market announcements dated
22 November 2021, 30 June 2023, 28 August 2024, 12 September 2024 and 3 October 2024, 8 November 2024, 19
November 2024 4 December 2024 and 16 December 2024 reported in accordance with the 2012 JORC Code and
available for viewing at www.criticalresources.com.au. The Company confirms that it is not aware of any new
information or data that materially affects the information included in any original ASX market announcement.
This information in this ASX Announcement that relates to the Halls Peak Mineral Resource Estimate is extracted from
ASX market announcement dated 30 June 2023 and reported in accordance with the 2012 JORC Code and available
for viewing at criticalresources.com.au. The Company confirms that it is not aware of any new information or data that
materially affects the information included in any original announcement and that all material assumptions and
technical parameters underpinning the estimates in the original market announcement continue to apply and have
not materially changed.
Halls Peak Project
Zn Cut-Off
Tonnage
JORC
Zn (%)
Pb (%)
Cu (%)
Ag ppm
Au pm
SG (calc)
grade (%)
(Mt)
Classification
Inferred
2.0
0.84
3.7
1.5
0.44
30
0.1
2.80
Total*
Inferred
0.84
3.7
1.5
0.44
30
0.1
*Reported at a cut-off grade of 2% Zn for an open pit mining scenario. Estimation for the model is from the generation of a rotated
block model, with blocks dipping 55>330o. Classification is according to JORC Code Mineral Resource categories. Refer to ASX
announcement 30 June 2024.
This document contains information relating to the Mineral Resource estimate for the Mavis Lake Lithium Project is
extracted from the Company’s ASX announcement dated 5 May 2023 and reported in accordance with the 2012
JORC Code and available for viewing at criticalresources.com.au. The Company confirms that it is not aware of any
new information or data that materially affects the information included in the original announcement and that all
material assumptions and technical parameters underpinning the Mineral Resource estimate continue to apply and
have not materially changed.
JORC Classification
Li2O Cut-Off grade (%)
Tonnage (Mt)
Li2O (%)
Inferred
Total*
0.3
Inferred
8.0
8.0
1.07
1.07
*Reported at a cut-off grade of 0.30% Li2O for an open pit mining scenario. Estimation for the model is by inverse distance weighting.
Classification is according to JORC Code Mineral Resource categories. Refer to ASX announcement 5 May 2023, 8.0 Mt at 1.07% Li2O
Maiden Mineral Resource at Mavis Lake.
Page 5 of 23
FORWARD LOOKING STATEMENTS This announcement may contain certain forward-looking statements and projections.
Such forward looking statements/projections are estimates for discussion purposes only and should not be relied upon.
Forward looking statements/projections are inherently uncertain and may therefore differ materially from results
ultimately achieved. Critical Resources Limited does not make any representations and provides no warranties
concerning the accuracy of the projections and disclaims any obligation to update or revise any forward-looking
statements/projects based on new information, future events or otherwise except to the extent required by applicable
laws. While the information contained in this report has been prepared in good faith, neither Critical Resources Limited
or any of its directors, officers, agents, employees or advisors give any representation or warranty, express or implied,
as to the fairness, accuracy, completeness or correctness of the information, opinions and conclusions contained in
this announcement.
Page 6 of 23
Appendix
Sample
Easting GDA94 56J
Northing GDA94 56J
Elev. (m)
Sb (%)
Sb (ppm)
Au (ppm)
Ag (ppm)
MVS2
400987
6614278
992
0.0132
132
0.35
0.03
MVS4
400967
6614270
982
0.328
3280
2.65
0.02
MVS5
400980
6614279
992
19.45
>10000
0.1
0.36
MVS6
400980
6614279
992
29.7
>10000
0.35
0.21
MVS7
400980
6614279
992
0.942
9420
0.03
0.06
MVS8
400980
6614277
992
38.3
>10000
0.31
0.74
MVS9
401013
6614191
989
8.8
>10000
0.29
0.29
MVS10
400810
6614320
995
0.797
7970
0.19
0.18
MVS10A
400922
6614238
987
0.0716
716
<0.01
0.03
MVS11
400905
6614288
983
15.35
>10000
2.71
0.77
MVS12
400889
6614309
982
7.36
>10000
0.71
0.44
MVS13
400883
6614303
983
0.737
7370
1.86
0.21
MVS14
400905
6614288
985
31.8
>10000
0.84
0.99
MVS15
400905
6614288
985
20.8
>10000
0.29
0.96
MVS16
400905
6614288
985
27.5
>10000
0.87
0.65
MVS17
400905
6614288
985
52.3
>10000
0.08
0.47
MVS18
400905
6614288
985
12.45
>10000
2.18
0.41
MVS19
400905
6614288
985
11.2
>10000
1.13
0.4
MVS20
400905
6614288
985
30.1
>10000
0.26
0.32
Table 1: Grab sample assay results at the Mayview Homestead Antinomy Prospect (Refer announcement 16
December 2024)
Thin Section Photographs
This appendix presents thin section photomicrographs of each rock sample analyzed in this study. Each
image is accompanied by a brief description highlighting the key petrographic features observed.
MVP3
Description: Finely recrystallized metamorphosed mudstone composed of sericite and quartz, with
intersecting quartz veins. Supergene goethite (orange-brown) and cervantite (yellow) overprinting earlier
quartz veins.
Page 7 of 23
Figure 3: Finely recrystallized mudstone with quartz veining. Transmitted light, crossed polarisers, field
of view 2 mm.
Figure 4: Supergene goethite and cervantite overprinting quartz vein. Plane-polarized oblique
reflected light, field of view 1 mm.
MVP4
Description: Metamorphosed siltstone with quartz-rich veining and hydrothermal breccia. Possible remnants
of pyrite, arsenopyrite, and stibnite replaced by goethite and cervantite.
Page 8 of 23
Figure 5: Bedding laminations in metamorphosed siltstone with quartz veining. Transmitted light,
crossed polarisers, field of view 2 mm.
Figure 6: Hydrothermal breccia zone with silicified host rock fragments. Transmitted light, crossed
polarisers, field of view 2 mm.
MVP5
Description: Low-grade metamorphosed siltstone with later quartz-rich veining. Stibnite replaced by
cervantite and goethite.
Page 9 of 23
Figure 7: Major quartz vein adjacent to hydrothermal breccia. Transmitted light, crossed polarisers,
field of view 2 mm.
Figure 8: Infill of major quartz vein with cervantite and remnant stibnite. Plane-polarized reflected
light, field of view 0.5 mm.
MVP11
Description: Metamorphosed siltstone with a large compound vein. Sulphide minerals replaced by goethite,
cervantite, and senarmontite.
Page 10 of 23
Figure 9: Compound vein with quartz and supergene goethite veining. Transmitted light, crossed
polarisers, field of view 2 mm.
Figure 10: Quartz-rich vein infill with relict arsenopyrite grains. Plane-polarized reflected light, field of
view 0.5 mm.
Page 11 of 23
Figure 11: Supergene oxidation products replacing stibnite in central vein. Plane-polarized
transmitted light, field of view 2 mm.
MVP14
Description: Stibnite-rich vein filling, with significant replacement by senarmontite and cervantite.
Figure 12: Stibnite enclosing quartz, replaced by supergene Sb oxides. Plane-polarized reflected light,
field of view 2 mm.
Page 12 of 23
Figure 13: Supergene Sb oxide with pseudomorphic texture after stibnite. Plane-polarized reflected
light, field of view 2 mm.
Figure 14: Deformation twinning and recrystallization in stibnite. Plane-polarized reflected light, field
of view 2 mm.
Page 13 of 23
Figure 15: Metallic antimony grains within supergene Sb oxides. Plane-polarized reflected light, field
of view 0.5 mm.
MVP16
Description: Supergene-affected stibnite-quartz vein filling, where stibnite is largely replaced by
senarmontite and cervantite.
Figure 16: Supergene Sb oxide phases with residual quartz. Plane-polarized reflected light, field of
view 2 mm.
Page 14 of 23
Figure 17: Relict stibnite grains enclosed in residual quartz. Plane-polarized reflected light, field of view
0.5 mm.
MVP18
Description: Metamorphosed, veined, and hydrothermally altered siltstone with supergene alteration
effects.
Figure 18: Syn-tectonic quartz veining in recrystallized metasiltstone. Transmitted light, crossed
polarisers, field of view 2 mm.
Page 15 of 23
Figure 19: Metasiltstone adjacent to quartz-sulphide vein, overprinted by clay and goethite. Planepolarized transmitted light, field of view 2 mm.
MVP19
Description: Strongly veined siltstone with stibnite-bearing quartz veins replaced by senarmontite and illite.
Figure 20: Narrow quartz veins in finely recrystallized metasiltstone. Transmitted light, crossed
polarisers, field of view 2 mm.
Page 16 of 23
Figure 21: Major quartz-stibnite vein replaced by Sb oxide and clay. Plane-polarized reflected light,
field of view 1 mm.
Page 17 of 23
JORC Code, 2012 Edition – Table 1
Section 1 Sampling Techniques and Data
(Criteria in this section apply to all succeeding sections.)
Criteria
JORC Code explanation
Sampling
• Nature and quality of sampling (e.g., cut
techniques
channels, random chips, or specific
specialised
industry
standard
measurement tools appropriate to the
minerals under investigation, such as
down hole gamma sondes, or handheld
XRF instruments, etc.). These examples
should not be taken as limiting the broad
meaning of sampling.
• Include reference to measures taken to
ensure sample representivity and the
appropriate
calibration
of
any
measurement tools or systems used.
• Aspects of the determination of
mineralisation that are Material to the
Public Report.
• In cases where ‘industry standard’ work
has been done this would be relatively
simple (e.g., ‘reverse circulation drilling
was used to obtain 1 m samples from
which 3 kg was pulverised to produce a
30 g charge for fire assay’). In other cases
more explanation may be required, such
as where there is coarse gold that has
inherent sampling problems. Unusual
commodities or mineralisation types (eg
submarine
nodules)
may
warrant
disclosure of detailed information.
Drilling
techniques
Drill sample
recovery
Logging
• Drill type (eg core, reverse circulation,
open-hole hammer, rotary air blast,
auger, Bangka, sonic, etc.) and details
(eg core diameter, triple or standard
tube, depth of diamond tails, facesampling bit or other type, whether core is
oriented and if so, by what method, etc.).
• Method of recording and assessing core
and chip sample recoveries and results
assessed.
• Measures taken to maximise sample
recovery and ensure representative
nature of the samples.
• Whether a relationship exists between
sample recovery and grade and whether
sample bias may have occurred due to
preferential loss/gain of fine/coarse
material.
• Whether core and chip samples have
been geologically and geotechnically
logged to a level of detail to support
appropriate Mineral Resource estimation,
mining studies and metallurgical studies.
Commentary
A series of historic antimony workings
comprising pits/shafts and trenches have
been mapped and sampled. The
workings were developed by miners in the
nineteenth century and have since been
infilled with soil and debris, resulting in the
exploration team being unable to access
the mineralised lodes which the miners
were working. However, there were
numerous mine dumps left by the old
miners which have been identified.
• The exploration crew had to dig into these
dumps to locate samples of mineralisation
previously overlooked. All samples are
from
loose
mineralised
lithologies
uncovered in what is interpreted to be old
mine dumps. Most of the samples
collected for analyses were limited to
individual rocks to avoid mixing out-ofcontext lithologies. Consequently, many
samples are of small mass. It must be
stressed that these samples are not
indicative of the average mineralisation
of the mineralised lodes as there was no
outcrop exposures of mineralisation.
• Recent thin section analysis conducted
on rock samples from key locations.
Standard petrographic methods used for
thin section preparation and description.
• Not applicable, rock sampling program
•
•
•
Not applicable, rock sampling program
Hand samples were collected and
prepared for thin section analysis with no
reported loss of material.
•
Not applicable, no drill hole data,
reporting data comprising rock samples.
Rock samples were collected in the field
by qualified field geologists and as part of
a
detailed
prospecting
program.
Qualitative categorical and descriptive
•
Page 18 of 23
Criteria
Subsampling
techniques
and sample
preparation
Quality
of
assay data
and
laboratory
tests
Verification
of sampling
and
assaying
Location of
data points
JORC Code explanation
Commentary
data was collected on each sample by
the field geologists along with a
representative photo collected of each
sample
• Not applicable, rock sampling program
• Detailed
petrographic
descriptions
recorded for each sample.
• If core, whether cut or sawn and whether
quarter, half or all core taken.
• If non-core, whether riffled, tube sampled,
rotary split, etc. and whether sampled wet
or dry.
• For all sample types, the nature, quality
and appropriateness of the sample
preparation technique.
• Quality control procedures adopted for
all sub-sampling stages to maximise
representivity of samples.
• Measures taken to ensure that the
sampling is representative of the in situ
material collected, including for instance
results for field duplicate/second-half
sampling.
• Whether sample sizes are appropriate to
the grain size of the material being
sampled.
• The nature, quality and appropriateness
of
the
assaying
and
laboratory
procedures used and whether the
technique is considered partial or total.
• For geophysical tools, spectrometers,
handheld XRF instruments, etc., the
parameters used in determining the
analysis including instrument make and
model, reading times, calibrations factors
applied and their derivation, etc.
• Nature of quality control procedures
adopted
(eg
standards,
blanks,
duplicates, external laboratory checks)
and whether acceptable levels of
accuracy (i.e. lack of bias) and precision
have been established.
• The verification of significant intersections
by either independent or alternative
company personnel.
• The use of twinned holes.
• Documentation of primary data, data
entry procedures, data verification, data
storage
(physical
and
electronic)
protocols.
• Discuss any adjustment to assay data.
• Accuracy and quality of surveys used to
locate drill holes (collar and down-hole
surveys), trenches, mine workings and
•
•
• Whether logging is qualitative or
quantitative in nature. Core (or costean,
channel, etc.) photography.
• The total length and percentage of the
relevant intersections logged.
•
•
•
•
•
•
•
•
•
•
•
•
Data comprising rock samples
No field sub-sampling techniques were
employed on the program.
All samples are from loose mineralised
lithologies
uncovered
in
what
is
interpreted to be old mine dumps. Most of
the samples collected for analyses were
limited to individual rocks to avoid mixing
out-of-context lithologies. Consequently,
many samples are of small mass. It must
be stressed that these samples are not
indicative of the average mineralisation
of the mineralised lodes as there was no
outcrop exposures of mineralisation.
Standard rock thin section preparation
and analysis using transmitted and
reflected light microscopy.
All samples reported herein were
collected by qualified geologists and the
nature, quality and appropriateness of
the assaying and laboratory procedures
used are detailed below.
All samples have been dispatched to ALS
Laboratories Zillmere, Queensland.
All samples - Preparation: PUL-31 Pulverize
up to 250g 85% <75 um
All samples - Analytical Method: AuMETL44 50g, 51 elements.
Visual petrographic assessment used to
confirm mineralogical composition.
No verification sampling and assaying has
been captured to date
No drilling
No adjustments to data
results
cross-checked
Petrographic
against
historical
grab
sample
descriptions.
All samples have been located by
handheld Garmin GPS 60x where the grid
datum GDA94 Zone 56J
Page 19 of 23
Criteria
Data
spacing and
distribution
JORC Code explanation
other locations used in Mineral Resource
estimation.
• Specification of the grid system used.
• Quality and adequacy of topographic
control.
• Data spacing for reporting of Exploration
Results.
• Whether
the
data
spacing
and
distribution is sufficient to establish the
degree of geological and grade
continuity appropriate for the Mineral
Resource and Ore Reserve estimation
procedure(s) and classifications applied.
• Whether sample compositing has been
applied.
Commentary
Thin section samples referenced
specific outcrop locations.
•
to
•
The decision on the spatial distribution
and distance of sampling has been
determined solely by the distribution of old
mine workings and mine dump and no
continuity of grade is implied
No sample compositing has been implied
The data spacing and distribution was not
intended and is not sufficient to establish
the degree of geological and grade
continuity appropriate for the Mineral
Resource and Ore Reserve estimation
procedure(s) and classifications applied.
The work completed was appropriate for
the current early exploration stage.
Thin sections selected based on field
observations and previous geochemical
data.
•
•
•
•
Orientation
of data in
relation
to
geological
structure
Sample
security
Audits
reviews
or
• Whether the orientation of sampling
achieves unbiased sampling of possible
structures and the extent to which this is
known, considering the deposit type.
• If the relationship between the drilling
orientation and the orientation of key
mineralised structures is considered to
have introduced a sampling bias, this
should be assessed and reported if
material.
• The measures taken to ensure sample
security.
•
•
•
No sample orientation was undertaken
No drilling undertaken or reported.
Thin sections prepared to evaluate key
mineralisation and alteration features.
•
Samples were in continual custody of
professional Company representatives
until final delivery by secure express
parcel post to the laboratory where all
sample will be held in a secure setting until
processing
• The results of any audits or reviews of
sampling techniques and data.
•
No audit has been undertaken at this
early stage of exploration
Page 20 of 23
Section 2 Reporting of Exploration Results
(Criteria listed in the preceding section also apply to this section.)
Criteria
JORC Code explanation
Commentary
Mineral
• Type, reference name/number, location
• CRR holds five granted Exploration
tenement
and ownership including agreements or
Licences (EL4474, EL7679, EL9428, EL9429,
and
land
material issues with third parties such as
EL9430), northeast of Armidale N.S.W.,
tenure status
joint ventures, partnerships, overriding
that encompass at total of 946km2.
• All tenements are granted.
royalties, native title interests, historical
sites, wilderness or national park and
environmental settings.
• Th
Share your feedback
Discover